Description
Tired of your 3 way caravan fridge not coping with hotter weather?
Our Klevacool™ Universal Fit Dual Fan Mod Kit can make a big difference!
This kit doesn’t include 3D printed fan mounting plates, so isn’t as neat as our other designs.
The fans & Klevacool™ controller are simply zip-tied to your existing vent.
Our fans are “smart fans”, that vary their speed to match your fridge operating conditions!
This means:
They’re more efficient as they only draw as much power as required to cool your fridge.
They shutdown if the blades are blocked by a foreign object – No burnouts!
They’re quieter when the ambient temperature is colder (usually at night!)
Our kits use our own design “Klevacool Electronic Fan controller”, rather than a simple thermo-switch.
Designed & assembled in Australia, for RV’s operating in harsh Australian conditions.
Switch selectable temperature settings.
Bypass/test switch for testing fans or in the unlikely event of controller failure.
Control status LED for a quick visual indication of fan status.
Over-temperature monitoring & alarm if temperature gets too high.
Seperate current protected output for internal fridge fan system.
Electronic reverse polarity protection to ensure full voltage is applied to the fans.
Extremely low current draw in standby mode (14mA).
Connection port for remote control (future feature)
Temperature sensor is built into the board, which means no dangling temperature probes.
Connector is quick & simple to disconnect if vent needs to be removed.
The fans are very simple to install using the included zip-ties & our highly detailed installation instructions.
The fitting of heat extracting fans to improve the efficiency of an absorption fridge is not a new idea, so what’s different about the 3DprintRV fridge fan system?
Controller bypass switch in the unlikely event of failure. Peace of mind!
Neat, professional finish.
Low standby power draw (14mA).
Simple connector system allows vent to be easily removed for maintenance.
Reverse power protection built in.
SMART FANS – Our fans move up to 1640l/min & vary their speed depending on system requirements. This means less noise, less wear & lower overall power consumption.
SMART FANS will simply stop if the blades are blocked & restart when they are free again. No burn outs!
Low current draw (0.25 amps in total).
A multicolour LED provides unobtrusive visual indication of what the fans are doing.
Over-temperature alarm alerts if temperature behind vent gets too high.
Simply requires 12v to be provided to the connector on the fan mounting plates. All other wiring is done.
System is fully tested before being sent to you.
No drilling required to mount the fans.
36 months warranty.
Important Notes
- These fans require 60mm of clearance from the front of the vent shroud to enable them to fit.
- This fan system is designed to fit any vent type. Fans are 120mm square & there are two. Some extra room is required to mount the quick connect board.
- The vents shown in the pictures are not supplied. The fans supplied in the kit are ZIP-TIED to your existing vent.
- Installation of these fans is simple, but a power supply is required for them to operate. Wiring will need to be installed from the van electrical system to the vent. 4 meters of wire is included.
- We don’t recommend connecting directly to the battery as this will bypass any battery low voltage protection devices in your van.
- If you are unsure how to install this wiring, please consult with your local auto electrician or caravan repair shop.
- Detailed installation instructions are included.
FANS
Size -120mm
Bearing – Hydrodynamic
Current draw – 0.25A total for two (6Ah/day at max speed)
Moves 58cfm (1640L/min) of air per fan (3280L/min total)
Ingress rating – IP54
INCLUDED IN KIT
3 x quiet, high quality brushless, smart fans
1 x 3D printed mounting for quick connect PCB
1 x fuse holder
2 x 3A fuses
4 meters of wire for battery connection.
Four pin connector
Short length of spiro wrap
zip ties in both black & white (to suit the colour of your vent)
Installation instructions
